Wednesday, August 19, 2015
CineStill 800T Test Run
Monday, July 20, 2015
News from the LRF
The film needs to cool and solidify the emulsion layer before it can be wound into a roll for later cutting to size. Due to the warmer weather, this now requires chilling equipment to be installed that was not planned until September. The first run was planned for cooler temperatures that did not require this equipment.
Despite these setbacks, Ferrania continues to plan to release its Kickstarter products, just on a different timeline.
Sunday, July 19, 2015
Tim Rudman's Photo Book on Iceland
Tim describes the Icelandic landscape as "a wonderful country of folklore and religion, of myth and magic and a land of awesome subterranean forces and stunning scenery." Tim is a leader and center of information for lith printing on silver-gelatin paper.
He also gives an excellent tip for an online photography magazine, the Looking Glass. Looking Glass covers all things in still film - large format, ambrotype, 35mm, you get it. While the zine does require Flash, it does feature artwork from notable film photographers.
The newsletter also mentions Ilford new Direct Positive printing paper. The paper is geared towards pinhole camera work, where a positive image is desired without an internegative or film negative. The paper can be used in any large format camera or LOMO cameras by cutting to size.
It is well worth signing up for Tim Rudman's newsletter.
Monday, July 6, 2015
CineStill Film
The color film is made by removing the remjet backing from movie film stock, then packaging the film in 35mm canisters for use in still film cameras. Because the antihalation layer (the remjet layer) has been removed, the film does show halation affects, or halos around bright objects. The film does offer cinematic color and the ability to work in daylight (50Daylight, or the 800T with an 85B filter) and low light situations (800T). This blogger is ordering a pack of this film to try out!
Also available from CineStill, is a B&W cinema film, based on Eastman Double-X 5222 film stock, called bwXX. It can be processed in a variety of developers and can be used indoors with tungsten light or outdoors in daylight.
Sunday, July 5, 2015
Why waste water? Use the Ilford Archival Wash Method
A brief description of the Ilford method for film developed in a spiral tank (including most roll films) taken from the previously mentioned document reads as follows:
• After fixing, [drain and -ed] fill the spiral tank with water at the same
temperature, +/- 5ºC (9ºF), as the processing solutions.
Invert the tank 5 times.
• Drain the water away and refill. Invert the tank 10 times.
• Once more, drain the water. Invert the tank twenty times and
drain the water away.
• Finally rinse with a few drops of ILFORD ILFOTOL Wetting
Agent (1:200) added to the rinse water.
This method works because the concentration of fixer in the film emulsion decreases rapidly with each change of water. Your blogger has used this method successfully for years. Checkout the data sheet from Ilford for complete details including washing RC and Fibre-Based prints.
Monday, May 4, 2015
R3 Monobath Developer
A 32 ounce bottle of the potion costs US$20 for those in the Continental US. At this time, the developer is not available outside this region. At 8 ounces a roll, this one stop solution costs only $5 per use and requires no special preparation other than warming in a warm water bath. Push and pull effects can be achieved with the developer. Increase the working temperature to 90 degrees for 1.5 stops push.
A quick review of the MSDS sheet for R3 Monobath shows that it is a solution of Kodak HC-110 developer combined with Rapid Fixer. HC-110 is reknowned for its long shelf life, so New55's claim of "Keeps for a long time" is probably true. Helpful if you only process a roll or two now and then. Convenience does sell, and it certainly sounds more convenient than mixing up the chemistry from powders!
If you have never done your own darkroom work, but would like to try processing film with this developer, simply fill a dish pan with warm water at about 85 degrees (measure with an inexpensive thermometer, guessing is difficult to get right). Wear nitrile or latex gloves when handling the developer. Place the developing olution into a smaller container (preferably a film developing tank, but not necessary), then measure the temperature until the solution is up to 80 degrees. Use enough water so that when the film tank is set in the pan, it is 3/4s submerged. The water should not be near the top of the film tank, as it may contaminate the developer solution. Add more warm water if the water in the pan gets cool, but keep the level below the top of the film tank. When ready, lights out, pull the film off the spool and carefully dunk into the film tank. A film spool helps to keep the film from touching itself, where the developer will not get a chance to work. Use an audio timer on your phone for timing, but do not use the phone for the first 2 minutes; the light from the screen will fog the film.
Saturday, May 2, 2015
One Hour Labs Fading Fast
With the decline of consumer use of film, the One Hour lab no longer has the influx of film to support the business. Pro labs were hit earlier in the cycle as pros moved away from film. Those that are still around, might be able to survive on the fine art photography or other businesses that pro labs may specialize in. Some of the pro labs may specialize in high end scanning, a service that consumer labs are unwilling to provide - consumers only ever got a scan suitable for a 4x6 print. Some minilabs could do higher resolution scans, but the function took so long most operators would not bother. Today, there may still be shops such as pharmacies that will send away film to a central lab. Turn around times may be a week or two, though.
Alternatives to colour print film, such as B&W or E6 slides, can be processed just as easily at pro labs as print film, giving a wider choice of materials. B&W is simple enough to process at home, negating a need for an outside lab in the first place. Shops likeB&H Photo, The Photo Formulary and others carry materials to process B&W film. There are even kits for E6 slide film and C41 colour print film to process colour film at home.
While it is sad to see a convenient and quick service for processing film go out of business, the film enthusiast of today still has plenty of choice in pro labs or do-it-yourself processing to make a go of it. There may even be a shop nearby that will do the job if one is willing to wait a week or two.